Part Number Hot Search : 
TINY45V TINY45V ALSS0042 ADM5170 TINY45V RODUCTS MLX90 CA3338E
Product Description
Full Text Search
 

To Download VRBC-10E1A0 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 NON-ISOLATED DC/DC CONVERTERS
4.5 Vdc - 14 Vdc Input 0.75 Vdc - 3.63 Vdc/10 A Output
VRBC-10E1Ax
RoHS Compliant
Rev.A
Non-Isolated High Efficiency Fixed Frequency Remote Sense Low Cost Under-Voltage Lockout (UVLO) Over Temperature Shutdown
Wide Input Wide trim OCP/SCP Remote On/Off Active Low/High (option) Industrial Temperature Range
Description
The Bel VRBC-10E1Ax is part of the non-isolate dc/dc power converter series. The modules use a SIP package. These converters are available in a range of output voltages from 0.75 Vdc to 3.63 Vdc over a wide range of input voltage (Vin = 4.5 Vdc - 14 Vdc). The efficiency is typically 94.3% at 3.3 Vdc output at 5.0 Vdc input at full load.
Part Selection
Output Voltage 0.75 V - 3.63 V Input Voltage 4.5 V -14 V Max. Output Current 10 A Max. Output Power 36.3 W Typical Efficiency 94.3% Model Number Active Low VRBC-10E1AL Model Number Active High VRBC-10E1A0
Notes: 1. Add "G" suffix at the end of the model number to indicate "Tray Packaging". 2. All part numbers above indicate RoHS 6. Change the second letter "R" to "7" for RoHS 5 part numbers.
Absolute Maximum Ratings
Parameter Input Voltage (continuous) Output Enable Terminal Voltage Ambient Temperature Storage Temperature Min -0.3 V -0.3 V -40 C -55 C Typ Max 15 V 15 V 85 C 125 C Notes
Note: All specifications are typical at 25 C unless otherwise stated.
Input Specifications
Parameter Input Voltage Vo,set < 3.0 V Vo,set 3.0 V Input Current (full load) Input Current (no load) Remote Off Input Current Input Reflected Ripple Current (pk-pk) Input Reflected Ripple Current (rms) I t Inrush Current Transient Turn-on Voltage Threshold Turn-off Voltage Threshold
2
Min 4.5 V Vo,set+1.5 V -
Typ 40 mA 2 mA -
Max 14 V 14 V 8.6 A 400 mA
Notes
An input line fuse must always be used.
-
0.2 A s 4.3 V 4.0 V
2
150 mA 0.4 A s 2
Tested with one 1000 uF/25V AL input capacitor with ESR=0.03ohm max and 4 x 47 uF/16V Tantalum capacitors with ESR=0.013 ohm max at 100 kHz, & simulated source impedance of 1000nH, 5 Hz to 20MHz.
Note: All specifications are typical at 25 C unless otherwise stated.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 * Tel 201-432-0463 * Fax 201-432-9542 * www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
4.5 Vdc - 14 Vdc Input 0.75 Vdc - 3.63 Vdc/10 A Output
Output Specifications
Parameter Output Voltage Set Point Load Regulation Line Regulation Regulation Over Temperature (-40 C to +85 C) Output Current Current Limit Threshold Short Circuit Surge Transient Ripple and Noise (pk-pk) Ripple and Noise (rms) Turn on Time Overshoot at Turn on Output Capacitance Transient Response 50% ~ 100% Max Load Settling Time 100% ~ 50% Max Load Settling Time Min -2% Vo,set 0A 0 uF Typ 0.1% Vo,set 0.1% Vo,set 0.3Vo,set 200% Io,out 1A s 30 mV 12 mV 8 mS 160 mV 50 uS 160 mV 50 uS
2
Max 2% Vo,set 10 A 3A s 80 mV 35 mV 20 mS 1% 5600 uF 2
Notes Vin=5 V & 12 V, full load
Tref=Ta, min to Ta, max
Tested with 0-20 MHz, with 10 uF tantalum capacitor & 1 uF ceramic capacitor at the output
VO = 0.75 V 3.63 V
di/dt=2.5 A/uS; Vin=5 V & 12 V; and with 470 uF Tantalum capacitor at the output
Note: All specifications are typical at nominal input, full load at 25 C unless otherwise stated.
General Specifications
Parameter Efficiency Vo=3.3 V Vo=2.5 V Vo=1.8 V Vo=1.5 V Vo=1.2 V Vo=0.75 V Efficiency Vo=3.3 V Vo=2.5 V Vo=1.8 V Vo=1.5 V Vo=1.2 V Vo=0.75 V Switching Frequency Over Temperature Shutdown Output Voltage Trim Range Remote Sense Compensation MTBF Dimensions Inches (L x W x H) Millimeters (L x W x H) Weight 2.0 x 0.5 x 0.32 50.8 x 12.7 x 8.13 7.1 g 265 kHz 0.7525 V 93.0% 92.0% 90.0% 89.0% 87.5% 81.0% 300 kHz 130 C 5,114,191 hours 335 kHz 3.63 V 0.5 V Calculated Per Bell Core SR-332 (IO = 80%Io,max; Vo=3.3 V; Vin=12 V; Ta = 25 C) Measured at Vin=12 V, full load 94.3% 93.0% 91.5% 90.8% 89.3% 83.0% Measured at Vin=5 V, full load Min Typ Max Notes
Note: All specifications are typical at 25 C unless otherwise stated.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 * Tel 201-432-0463 * Fax 201-432-9542 * www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
4.5 Vdc - 14 Vdc Input 0.75 Vdc - 3.63 Vdc/10 A Output
Control Specifications
Parameter Remote On/Off Signal Low (Unit Off) Signal High (Unit On) Signal Low (Unit On) Signal High (Unit Off) -0.2 V -0.2 V 2.5 V 0.3 V Vin, max 0.3 V Vin, max VRBC-10E1A0; Remote On/Off pin open, Unit on. VRBC-10E1AL; Remote On/Off pin open, Unit on. Min Typ Max Notes
Output Trim Equations
Equation for calculating the trim resistor (in ) given the desired output voltage (Vo) is shown below. The Trim Up resistor should be connected between the Trim pin and Ground.
Vout
Sense
Rtrim =
10500 - 1000 Vo - 0.7525
Module
trim
Rtrim
GND
Equation for calculating the trim voltage (in V) given the desired output voltage (Vo) is shown below. The Trim Up voltage should be connected between the Trim pin and Ground.
Vout
Vtrim = 0.7 - 0.0667 x (Vo - 0.7525)
Sense
Module
trim
Vtrim
GND
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 * Tel 201-432-0463 * Fax 201-432-9542 * www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
4.5 Vdc - 14 Vdc Input 0.75 Vdc - 3.63 Vdc/10 A Output
Efficiency Data
Module 3.3 V 100.0% Efficiency 90.0% 80.0% 70.0% 1A 2.5 A 5A 7.5 A 10 A Output current 5.0 V 12.0 V
Efficiency 100.0% 95.0% 90.0% 85.0% 80.0% 75.0% 1A 2.5 A
Module 2.5 V
5.0 V 12.0 V
5A
7.5 A
10 A
Output current
Module 1.8 V 100.0%
Module 1.5 V 100.0% Efficiency
5.0 V 12.0 V
Efficiency
90.0% 80.0% 70.0% 1A 2.5 A 5A 7.5 A 10 A Output current
90.0% 80.0% 70.0% 1A 2.5 A 5A 7.5 A 10 A Output current
5.0 V 12.0 V
Module 1.2 V 100.0% Efficiency 5.0 V 12.0 V
Efficiency 100.0% 90.0% 80.0% 70.0% 60.0%
Module 0.75 V
90.0% 80.0% 70.0% 60.0% 1A 2.5 A 5A 7.5 A 10 A Output current
5.0 V 12.0 V
1A
2.5 A
5A Output current
7.5 A
10 A
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 * Tel 201-432-0463 * Fax 201-432-9542 * www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
4.5 Vdc - 14 Vdc Input 0.75 Vdc - 3.63 Vdc/10 A Output
Thermal Derating Curves
Vin=12 V, Vo = 3.3 V
Vin=5 V, Vo = 3.3 V
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 * Tel 201-432-0463 * Fax 201-432-9542 * www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
4.5 Vdc - 14 Vdc Input 0.75 Vdc - 3.63 Vdc/10 A Output
Ripple and Noise Waveforms
Vin=5 V, Vo=0.75 V
Vin=12 V, Vo=0.75 V
Vin=5 V, Vo=3.3 V
Vin=12 V, Vo=3.3 V
Note: Ripple and noise at full load, external load with 10 uF tantalum capacitor and 1 uF ceramic at the output, and Ta=25 deg C.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 * Tel 201-432-0463 * Fax 201-432-9542 * www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
4.5 Vdc - 14 Vdc Input 0.75 Vdc - 3.63 Vdc/10 A Output
Transient Response Waveforms
50% to 100% load Transient at Vin=5 V, Vo=0.75 V
100% to 50% load Transient at Vin=5 V, Vo=0.75 V
50% to 100% load Transient at Vin=12 V, Vo=0.75 V
100% to 50% load Transient at Vin=12 V, Vo=0.75 V
50% to 100% load Transient at Vin=5 V, Vo=3.3 V
100% to 50% load Transient at Vin=5 V, Vo=3.3 V
50% to 100% load Transient at Vin=12 V, Vo=3.3 V
100% to 50% load Transient at Vin=12 V, Vo=3.3 V
Note: Transient response at di/dt=2.5 A/uS, external load with 470 uF tantalum capacitor at the output.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 * Tel 201-432-0463 * Fax 201-432-9542 * www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
4.5 Vdc - 14 Vdc Input 0.75 Vdc - 3.63 Vdc/10 A Output
Mechanical Outline
Pin Connections
Pin 1 2 3 4 5 6 7 8 9 10 11 Function Vout Vout Remote Sense Vout Ground Ground Vin Vin N/A Trim Remote On/Off
RoHS Compliance
Complies with the European Directive 2002/95/EC, calling for the elimination of lead and other hazardous substances from electronic products.
(c)2007 Bel Fuse Inc. Specifications subject to change without notice. 011707
CORPORATE Bel Fuse Inc. 206 Van Vorst Street Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com
FAR EAST Bel Fuse Ltd. 8F/ 8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel 852-2328-5515 Fax 852-2352-3706 www.belfuse.com
EUROPE Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. Tel 44-1772-556601 Fax 44-1772-888366 www.belfuse.com


▲Up To Search▲   

 
Price & Availability of VRBC-10E1A0

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X